Steel profile beam turning over machine with motor chain drive
**Flipping machine introduction
1)The flipping tires work on turning products in 360 degree so as to adjust the position of the product.The equipment structure is like upside-down gantry type. It has four reducer to control the product piece and very convenient to apply when flipping.
2)The flipping tires are consist of swing arm, pillar and reset device, electric control and operating system. It also includes four standing columns attached with driving mechanism on each top. The brake motor controls the cycloidal pinwheel reducer to drive the sprockets.
3)The chain wheel is equipped with two pulley, the pulley installed on the swing arm.On the role of the pulley is change the movement direction of the chain and chain extension. There is a guide wheel close to the bottom of the chain wheel , that use for increasing the angle on the sprocket chain.
4)By using the post box welded structure, with enough stiffness and strength, the four standing columns are capable of using a long period with outstanding stability.
5)There are a swing arm and a heavy hammer device on the standing columns. When the workpiece need to flip, the swing arm goes downward with a certain angle. If there is no need to flip over the work piece, the swing arm is raised, and the chain is loosen, so as to make the workpiece either delivered neatly .
6)The flipping tires have lifting chain to rotate the work piece, so as to solve the problem of work piece turn slippy. There are four reducers can turn direction, either same-directional or reverse rotation. Same-directional rotation is to flip artifact,and reverse rotation is to lift artifacts.
7)To reach the length requirement of work pieces, one side standing columns are designed fixed while the other side of two columns respectively equipped with a sliding seat. Please fix both sides before use.
8)Control system includes: main control cabinet hand control box, hand control box with 15 meters cable connected to the control cabinet, hand control box can be used in different location of the equipment to operate equipment.
9)The manual operation box and master ark with buttons, such as power up, stop, reverse direction selector switch and abrupt stop button.
10)Control system has motor over-current, over-voltage and over torque protection.
11)Control system is equipped with temperature detection device, stop and alarm when over-temperature.
12)Control system has simple and convenient operation, reliable operation. The operation can be close to control or remote control operation, and it is convenient to the operator at any location.
**Flipping machine parameter
|Left-right Column Center Distance||1500mm|
|Front-back Column Center Distance||3000mm-5500mm(Depends on work piece length)|
|Flipping Machine Motor Power||1.1kw×4|
|Input Voltage||3PH 380V/50Hz|
Warranty: 12 months from the date of Bill of Lading.
The Seller shall bear responsibility for the entire machineries normally working during 12 months from the date of Bill of Lading. During warranty period, if are damages and disorders of equipment due to machine quality, The Seller shall be responsible for replacement of the defective parts with new parts. The warranty shall also include performance functions as defined in the offer. In the case that there is any defect The Buyer shall inform The Seller in writing and photos of the broken parts. The Seller will assist and deal with such damages within 15 days from receipt of The Buyer's above information.
The Seller doesn't guarantee the spare parts which are easily worn out / damaged. The Seller deems it his responsibility to furnish The Buyer these spare parts at prices reasonable or agreed.
The Seller doesn't guarantee equipment in case faults caused by operators' improper operation or electric source's breakdown.
1) When Sellers send engineer to Buyer's place for Installation, Commissioning and training for the machine in this contract in Buyer's place, Buyer shall undertake all the relative fees like, all tickets, accommodation for Seller's engineers.
2) Seller shall, within one week of receiving the above information, provide the required and qualified personnel to undertake supervision of installation, commissioning and training.
3) If the Buyer needs the service after sales from Seller, then Buyer shall undertake all the relative fees, like Round Tickets, Accommodation, Internal and international transportation, Labour cost of engineers etc.
4) When the Seller's engineer carries out the services in Buyer's place, Buyer shall arrange a Translator that can speak Chinese for Seller's engineer.
5) Labour cost for engineers: 80.00 USD per person, per day.